How To Refurbish An Old Craftsman Table Saw

Refurbish An Old Craftsman Table Saw Free For Another#

To replace this carriage bearing you will need a wrench to remove/secure eccentric screw that holds it to the carriage base. Includes one sealed metal bearing per order. This replacement part is sourced directly from original equipment manufacturer for use with Craftsman radial arm saws.

Sears and Craftsman, the Sears brand of tools, have been building tools for well over 50 years. And Sears PartsDirect has more table saw DIY repair help for you, including troubleshooting advice and maintenance tips for Craftsman, DeWalt, Delta and. Whether you're replacing the motor brushes or adjusting blade alignment, our repair guides and videos provide step-by-step instructions to help you complete the repair. I currently use my DadвЂ™s Makita 1/2 horse but thatвЂ™s not strong enough for some of the needs IвЂ™ve had so I figured it was time to break out the big boy and put it to back to work.Table saw repair guides. Find genuine replacement parts along with great repair advice and same-day shipping.I got up yesterday to a slow day in the shop with very little to do, and sometime mid-morning decided I wanted to get PapaвЂ™s table-saw out of storage before it got into any worse shape and see if I could restore it and build a table for it so I can use it in the shop.

Since IвЂ™m missing a few pieces, sheвЂ™ll weight about half that when IвЂ™m done.What youвЂ™re seeing here is the table turned upside down and the base removed. This big girl here when completely assembled weighs in at about 400 pounds with all the accessories mounted. TheyвЂ™re in pretty nasty shape too.Just as a side note, my entire Makita table saw (including the table, saw motor, blades, case AND stand, only weighs about 40 pounds. You can see the table (the cast-iron top) is extremely rust covered and in need of some real love and attention.The base (the big box that hides the inner guts) isnвЂ™t in much prettier shape itself showing signs of rust, dents, dings, scratches and 40 years of use.This inner workings (also made of cast iron) that make up the working parts of the saw are mounted to whatвЂ™s called the Cradle the big piece of iron that hangs down from the middle of the table. LolThis is the saw when I first brought it out of storage.

I tried adjusting the saw before I took it apart, but the tilt screw and height screws are so caked with gunk as to make it too much work. Believe it or not thatвЂ™s 40 years of caked sawdustвЂ¦ I had to literally break some of it off with a chisel to get it off!The tilt screw and other adjustment mechanisms are caked with sawdust, but otherwise undamaged over the years, but IвЂ™m still going to have to take it completely apart to regrease them. That brown and tan stuff isnвЂ™t actually rust.

Cleaning it was easier than youвЂ™d imagine. I took this picture just so I could remember which trunnion went on the front of the saw since they look almost identical, but one is for the front and one is for the back.Once completely removed the cradle is ready to work on.Amy took a picture about halfway through the process.The finished cradle turned out beautifully. The cradle glides inside the lip for left-to-right adjustment of the blade tilt. ItвЂ™s incredibly thin sheet aluminum so itвЂ™s not really easy to work with without breaking it.Those silver aluminum guides are called trunnions. The front panel canвЂ™t be replaced since Sears no longer carries that part so IвЂ™m going to have to do the best I can with restoring the one IвЂ™ve got.

I just blew it dry with the air-compressor in a couple seconds.My dad was famous for initialing everything in his shop. I didnвЂ™t even have to wipe it down afterwards. This side was completely cleaned using only WD-40 and a kerosene-soaked rag. IвЂ™d suggest WD-40 before you even try getting a grinder-wheel in those small spaces. Here you can see all the divots and recesses.

If youвЂ™re cutting 4x4 pilings or hardwood all the time the original motor is too weak, so carpenters often replace the motor of some of their saws with stronger ones for larger jobs. My dad replaced it sometime back (like many otherвЂ™s did) with a stronger motor. The Craftsman 113.29660 saw came from sears with a 3/4 horsepower sears motor rated for 110V. As you can see here itвЂ™s pretty dirty, even after being cleaned out with the air compressor.NOTE: If youвЂ™re reconditioning something like this for use in your shop as a hobby, be very careful with the motor youвЂ™re using. Now that I know it works, I figured IвЂ™d better see what kind of shape itвЂ™s in. Earlier in the day I rewired the motor and tested it.

(Considering I only have a dedicated 20-Amp breaker for it I guess I might be rewiring my house again in the coming monthsвЂ¦ sigh.)ItвЂ™s really important to be extremely careful with these big motors. On 110V this motor can draw up to 22 amps. My shop is only wired with 110V at the moment so I had to rewire the motor to work with my power requirements. Dual voltage means it can run on 110V or 220V, depending on the need. Reversible means of course that it can be wired to spin in either direction. This is a 2HP WEG reversible, dual voltage, motor.

I mean it took a 20 pound piece of lumber and shot it like a cannon right through a wooden wall about 12 feet away. I donвЂ™t mean it hit it and knocked a hole in it. Since itвЂ™s 4 times as powerful as the other motor, rather than bogging down and stopping the motor, this motor grabbed the 2x4 and hurled it backwards so hard that the board went THROUGH the wall behind it. Either a nail or an extremely dense knot caught the blade. I remember as a kid that dad was running a piece of 2x4 through it. This saw however it another story.

IвЂ™m not an electrician by any means but I can only imagine what would happen if you fired this thing up with solvent still inside the motor. Do NOT clean something like this with a flammable solvent, or really ANY kind of solvent in my opinion. Not too bad but needs cleaning. And if you do, be cognizant of it at all times.A closer look at the electromagnet inside the motor. If you donвЂ™t NEED a strong motor, donвЂ™t use one.

Refurbish An Old Craftsman Table Saw Free For Another

Click here.IвЂ™m still a long way from that, but IвЂ™ll get the parts together somehow and get her completed one day. Now I just need to wait for my new motor mount to come in from eBay and then I can get her working again.If you want to see what a guy can REALLY do when he sets his mind to restoring one of these, check out this guyвЂ™s restoration. Lol)This is a front view once sheвЂ™s been reassembled. (I figure that ought to keep it rust free for another 20 years or so. I cleaned the wheel assembly (the handle) carefully with a wire-wheel on low speed, repainted the base, and coated the underside of the table with engine enamel.

How to Update your Droid X if youвЂ™ve removed bloat.

How To Refurbish An Old Craftsman Table Saw